NUS Engineering team develops novel technology to "print" customised tablets for personalised medicine

SINGAPORE, May 26, 2016 /PRNewswire/ -- A team of researchers from the National University of Singapore (NUS) have found a way to make personalised medicine cheaper and easier. Imagine if you could combine the myriad of pills you need to take for your ailment in just one tablet; or if you need only to take the medication once a day and the drug will be slowly released throughout the day at different rates to treat your illness; or if doctors could easily make tablets on the spot that are tailored to each patient's needs.

All these could become a reality with a new method of tablet fabrication designed by Assistant Professor Soh Siowling and PhD student Ms. Sun Yajuan from the Department of Chemical and Biomolecular Engineering at the NUS Faculty of Engineering. The novel system can make customisable pills that release drugs with any desired release profiles.

Customised tablets for optimal therapeutic results

Releasing drugs in a timely manner is important for optimal therapeutic effect in the human body. Different types of clinical circumstances may call for different types of timed release of drugs.

One common type of release profile is that of a constant one: the drug is released at the same rate for a period of time, as there is only a narrow range of concentration in which the drug can be effective. However, certain chemicals, such as hormones, may need to be released in pulses at regular intervals, in sync with the biological cycles of the human body. In situations where a relatively large dose of drug is needed initially to act against their targets rapidly, followed by gradually lower levels to maintain health -- for example, in arthritis, a large dose is required initially to eliminate pain in the morning, followed by smaller doses to keep the pain from recurring -- a decreasing release profile would be appropriate.

While there are some existing tablet-production methods, including 3D printing, that can allow certain flexibility, they have their limitations -- low dosage, release profiles that are non-continuous, or the drugs are released in a large burst in the initial stage, and poor durability of the tablet given its quick breakdown. These methods are also only able to fabricate tablets that release drugs with a limited type of profiles.

A fully customisable fabrication method

"For a long time, personalised tablets has been a mere concept as it was far too complex or expensive to be realised. This new tablet fabrication method is a game changer -- it is technically simple, relatively inexpensive and versatile. It can be applied at individualised settings where physicians could produce customised pills on the spot for patients, or in mass production settings by pharmaceutical companies," said Asst Prof Soh. 

Instead of manufacturing the drug tablet by printing layer by layer, the drug tablet designed by Asst Prof Soh and Ms Sun consists of three distinct components, including a polymer containing the drug in a specifically designed shape that will determine the rate of release of the drug. For instance, a 5-prong shape will allow the drug to be released in five pulses over time. By adjusting the shape of the drug-containing polymer, it is thus possible to release drugs at any desired rate.

Using the system designed by the NUS team, a doctor only needs to draw the desired release profile in a computer software to generate a template for making tablets specific to a patient's treatment, which can then be used to easily produce the desired pills using a 3D printer. The system is easy to use and does not involve any complex mathematical computation whenever a new release profile is needed. The fully customisable system is able to create a template to print tablets for any release profile.

The use of a commercially available 3D printer in this method also makes it a relatively cheap way of making personalised medicine a reality, as compared to conventional tablet production or other methods in making small shapes, such as photolithography.  

In drug delivery, it is also often important to administer more than one type of drug into the human body simultaneously to treat an illness. The fabrication method developed by Asst Prof Soh can be modified to include multiple types of drugs loaded within the same tablet -- and more importantly, each drug can be customised to release at different rates even within the same tablet.

Aside from exploring commercialisation possibilities, the NUS team is currently doing further work to explore the various combination of materials for the different polymer-based components in the tablet to cater to various types of drugs and illnesses to increase the efficacy of this method.

Logo - http://photos.prnewswire.com/prnh/20151130/291548LOGO

SOURCE National University of Singapore